Search

Results

reviews:electricimp: 11 Hits

internal pull up hardware.pin9.configure(DIGITAL_OUT_OD_PULLUP); // Configure pin 8 as an open drain o... internal pull up hardware.pin8.configure(DIGITAL_OUT_OD_PULLUP); // Register with the server imp.con... lass impeeIn extends InputPort { name = "UART Out"; type = "string"; // This function ... aracter was sent to the impee // and sends it out over the UART5/7. We'll also toggle the txLed

projekte:nn_bot: 11 Hits

R IR: 0.40 L IR: 0.90 Output Nodes : 0.98 : 0.11 Out R Mot: 0.98 L Mot: 0.11 Test Input: R IR: 0.90 L IR: 0.90 Output Nodes : 0.85 : 0.86 Out R Mot: 0.85 L Mot: 0.86 Test Input: R IR: 0.70 L IR: 0.30 Output Nodes : 0.15 : 0.96 Out R Mot: 0.15 L Mot: 0.96 </file> Jetzt folgt das wirkliche fahren. Da... 0.74 L FL IR: 0.59 Output Nodes : 0.89 : 0.54 NN Out R Mot: 0.89 L Mot: 0.54 - Set Speed R MOT: 166 L

mqtt:start: 8 Hits

x509 -days 1999 -extensions v3_ca -keyout ca.key -out ca.crt </code> Erzeugen eines Server Schlüssels: <code bash> sudo openssl genrsa -out server.key 2048 </code> Certificate Signing Request erzeugen: <code bash> sudo openssl req -out server.csr -key server.key -new </code> Selber signieren: <code ... ver.csr -CA ca.crt -CAkey ca.key -CAcreateserial -out server.crt -days 365 </code> == Serverkonfigurat

wireless:wifi: 7 Hits

NG NEGLIGENCE OR // OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF // ADVISED O... char tpl[] = "%s:%s:%s:%s:%s:%s:%d:%d:%d"; char out_string[64]; char temp1[6]; char temp2[6]; c... } } else { pir_status = 0; } sprintf(out_string, tpl, temp1, temp2, temp3, hyg1, c_target_... ,3), pir_status); #ifdef SBDG Serial.print("OUT: "); Serial.println(out_string); #endif

tutorials:start: 6 Hits

s und IR - Melder von //AS// * {{:tutorials:i2c-out1.pdf|I2C - Bus und Out 1}} von //AS// * {{:tutorials:i2c-out2.pdf|I2C - Bus und Out 2}} von //AS// * {{:tutorials:i2c-out2-code.zip|Demo Programme und Bibliotheken}} für I2C - Bus und Out 2 * {{:tutorials:i2c-schalter1.pdf|I2C - Bus und Scha... ür I2C-Bus und Schalter 2 * {{:tutorials:i2c_in-out1.pdf|I2C - In / Out 1}} von //AS// * {{:tutoria

arduino:arduino_massprogramming: 2 Hits

from Arduino directoy and save output for later: OUT=$($ARDUINO_BASE/hardware/tools/avrdude -v -C$ARDU... ming board:" | /usr/bin/logger /bin/echo $OUT | /usr/bin/logger /bin/echo -e "\007" > /

arm:cubieboard_comparison: 2 Hits

/td> </tr> <tr> <td> <strong>Video Out</strong></td> <td> HDMI</td> <td> ... /td> </tr> <tr> <td> <strong>Audio Out</strong></td> <td> HDMI/ SPDIF/ Headphon

helvepic32:bspringcoderfinal:start: 2 Hits

sb; datamsb = (data&0xFF00)>>8; // mask out the MSB and shift it right 8 bits datalsb = data & 0xFF; // Mask out the LSB Serial.print(" "); Serial.print(datamsb,DEC);

helvepic32:bspshiftreg:start: 2 Hits

sb; datamsb = (data&0xFF00)>>8; // mask out the MSB and shift it right 8 bits datalsb = data & 0xFF; // Mask out the LSB Serial.print(" "); Serial.print(datamsb,DEC);

helvepic32bb:bspn5110:start: 2 Hits

bbd3.png?800|}} nun SDA, besser als MOSI (Master Out, Slave In) {{:helvepic32bb:helvepic32bbd4.png?80... al.print("Error"); Serial.print("ACK time out "); break; case DHT_ERROR_SYNC_TIME

helvepic32:elecfreakskit:start: 2 Hits

6 pin,driving the Passive buzzer,the pin must PWM out(3 5 6 9 10 11) #elif defined(__PIC32MX__) #includ... timing highpulse = lowpulse = 0; // start out with no pulse length while (IRpin_PIN & (

sensors:input_multiplexer_cd4051: 2 Hits

4 = 9 (S2) A7 = 3 (In Out) GND = 6 (ING) GND = 7 (Vee... 4 = 9 (S2) A7 = 3 (In Out) GND = 6 (ING) GND = 7 (Vee

helvepic32:bspi2calphanum:start: 1 Hits

eDigitAscii(3, displaybuffer[3]); // write it out! alpha4.writeDisplay(); delay(200); }</code>

arduino:attinyusb:helvetiny85: 1 Hits

nucleus/zip/master]] - Arduino IDE meldet "time out" beim hochladen. => Helvetiny85 nochmals komplett

linux:start: 1 Hits

wiki:dokuwiki: 1 Hits

arduino:attinyusb:helvetiny85:tutorials: 1 Hits

arduino:start: 1 Hits

wireless:lorabee: 1 Hits

wireless:esp8266: 1 Hits

wiki:syntax: 1 Hits